|
<br />specifications
<br />
<br />-
<br />
<br />ordering information
<br />
<br />HOUSING shall be fabricated from a one-piece extruded
<br />aluminum side panel with mitred corners that are
<br />internally welded and sealed for weathertight integrity.
<br />A press-formed aluminum top cover shall interlock with
<br />the housing and have a continuous weathertight seal and
<br />a 314" high peaked center for increasE;d strength and
<br />efficient water run off.
<br />
<br />LENS FRAME ASSEMBLY shall consist of a K6" thick
<br />impact resistant clear tempered safety glass lens
<br />enclosed by a one-piece molded high temperature
<br />gasket. Tempered glass shall conform to USA Standard
<br />Safety Codes (USAS) Z26.1 and Z97.1 and Federal
<br />Specification DD-G-451 C. Lens and gasket shall be
<br />retained in an extruded aluminum frame which shall be
<br />hinged at the pole end and shall close and seal the
<br />optical chamber by four (4) gasketed vibration proof
<br />quarter-turn fasteners,
<br />
<br />II
<br />II
<br />II
<br />II
<br />I
<br />I
<br />I
<br />
<br />OPTICAL CHAMBER shall consist of a one-piece
<br />hydroformed Kim Asymetron Reflector with a highly
<br />specular Alzak@ processed surface and an adjustable
<br />socket assembly for ANSI type III or type II distribution.
<br />Reflector shall incorporate an integral down light
<br />diffusing facet to eliminate excessive illumination directly
<br />under the fixture. Reflector and lens frame assembly
<br />shall form a hermetically sealed chamber for highly
<br />reduced maintenance and cleaning, All wires to the lamp
<br />holder shall be sealed at point of entry into the optical
<br />chamber. Lamp holder shall be porcelain mogul base
<br />with vibration proof lamp grip shell.
<br />
<br />I
<br />i
<br />I
<br />I I
<br />
<br />ALL ELECTRICAL COMPONENTS shall be UL approved
<br />and be an integral part of the fixture. Ballasts and related
<br />components shall be integrated onto a single mounting
<br />plate as a self-contained subassembly, To facilitate fast
<br />assembly and maintenance, this electrical subassembly
<br />shall be attached to the fixture with quick disconnecting
<br />hinges. Fast field wiring shall be provided for by
<br />pre-wiring all electrical components with quick disconnect
<br />plugs, All ballasts shall be of the component type
<br />regulating autotransformer with power factor better than
<br />0,90 (HPF). Ballasts shall be one of the following types
<br />as required: Mercury ballasts shall provide :i:5% lamp
<br />power regulation and :i:10% input voltage regulation, High
<br />Pressure Sodium ballasts shall provide :i:10% lamp
<br />power / :i:5% input voltage or :i:5% lamp power /
<br />:i:10% input voltage regulation, as required. Metallic
<br />Halide ballasts shall provide :i:7% lamp power regulation
<br />and :i:10% input voltage regulation.
<br />
<br />FIXTURE ARM shall be a one-piece rectangular aluminum
<br />extrusion with internal centering guides. Luminaire-to-
<br />pole assembly shall be made through a mechanical
<br />attachment within the arm, eliminating all exposed
<br />fasteners or welds, Arm assembly shall include a pole
<br />reinforcing plate which will mount inside the pole for
<br />added strength at the arm joint.
<br />
<br />FINISH on luminaire and arm shall be semi-gloss black
<br />(or bronze) baked enamel applied over a clear anodized
<br />base, (optional anodized colors available on request).
<br />
<br />4 Kim Lighting, Ine,
<br />
<br />
<br />2V2"
<br />
<br />28V2"
<br />
<br />8"
<br />
<br />iIlI
<br />
<br />"...,'.,'~",.,.",
<br />{'~~~;~; ;:~. .
<br />
<br />t't:.l:.~;:, ,-
<br />
<br />'~ .~ ~.:~o~t :
<br />..,~.
<br />',' . ,. .," ',.~
<br />. .:<..
<br />
<br />r:I
<br />
<br />6"
<br />
<br />-=
<br />NOTE: Standard arm length is 8" on all poles, however,
<br />shorter arms can be provided for A and B mountings if
<br />a more compact look is desired, On square poles, arms
<br />can be completely eliminated for A and B mountings,
<br />Consult factory for details.
<br />
<br />standard mounting arrangements
<br />III
<br />
<br />
<br />A __
<br />
<br />B ____
<br />
<br />f~fft:;",;~:;,~~lS."
<br />
<br />;,/' ",," '~ti...,
<br />j,51;''';~~ -"
<br />
<br />';,,:,"- '.~.
<br />
<br />
<br />EI
<br />
<br />.-;::1.':("
<br />
<br />\~I-':..;...
<br />"
<br />
<br />'.\~-""~-
<br />
<br />"~;'~~':;,\:_";.t.,- .. ,
<br />
<br />~',",>;'~NOTE':M~ounhl1gs A, B,anCl C are most commonly used
<br />'-. ~'-kl~..~-",'~' ~~~ ',> ,': " ,~
<br />{1.;.J:~na~;wrIL ,pt:1dtom.etrically suit almost every application,
<br />;.~j~Tqnalry special arrangements are required which
<br />'f'?:~~-e:):~ provide because of our flexible attachment sys-
<br />.t~;re1ri;);!~lways consult the factory for any mountings other
<br />_~:~ft~'n'tXRes A, B, or C.'See page 11 for other suggestions.
<br />:?r~~~fi:~'=~' a
<br />
<br />c
<br />
<br />o
<br />
<br />III
<br />
<br />o
<br />
<br />o
<br />
<br />()
<br />
<br />Fixture Line Ballast Regulation Line Operating Starting
<br />Cat. No, Lamp Volts Line Volts Lamp Watts Watts Amps Amps
<br />EKG-100 120 :i: 10% :i: 7% * 462 4,00 2,50
<br />EKG-101 400 Watt 208 :i: 10% :i: 7% * 462 2,30 1.45
<br />EKG-102 Metallic Halide 240 :i: 10% :i: 7% * 462 2,00 1,25
<br />EKG-103 277 :i:10% :i: 7% * 462 1,75 1.10
<br />EKG-104 480 :i: 10% :i: 7% * 462 1,00 0,63
<br />EKG-110 120 :i: 5% :i: 10% . 450 4,00 6.40
<br />EKG-111 120 :i:10% :i: 5% . 470 4,00 4.00
<br />EKG-112 208 :i: 5% :i: 10% . 455 2,30 3,80
<br />EKG-113 400 Watt 208 :i:10% :i: 5% . 470 2,30 2,30
<br />EKG-114 240 :i: 5% :i: 10% . 440 2,00 3,65
<br />EKG-115 High Pressure 240 :i: 10% :i: 5% . 470 2.10 2,10
<br />EKG-116 Sodium 277 :i: 5% :i: 10% . 455 1,70 2.85
<br />EKG-117 277 :i:10% :i: 5% . 470 1.80 1,80
<br />EKG-118 480 :i: 5% :i: 10% . 460 1,00 1,65
<br />EKG-119 480 :i: 10% :i: 5% . 490 1,10 1.10
<br />EKG-125 120 :i:10% :i: 5% * 450 3.90 3,10
<br />EKG-126 400 Watt 208 :i: 10% :i: 5% * 450 2,20 1,82
<br />EKG-127 Mercury Vapor 240 :i: 10% :i: 5% * 450 1,95 1,60
<br />EKG-128 277 :i:10% :i: 5% * 450 1.70 1,35
<br />EKG-129 480 :i: 10% :i: 5% * 450 0.98 0,80
<br />EKG-135 120 :i:10% :i: 5% . 325 2,80 2.80
<br />EKG-136 250 Watt 208 :i: 10% :i: 5% . 325 1,60 1,60
<br />EKG-137 High Pressure 240 :i: 10% :i: 5% . 325 1.40 1.40
<br />EKG-138 Sodium 277 :i: 10% :i: 5% . 325 1,20 1,20
<br />EKG-139 480 :i: 10% :i: 5% . 325 0.70 0,70
<br />EKG-145 120 :i:10% :i: 5% * 285 2.50 1.80
<br />EKG-146 250 Watt 208 :i:10% :i: 5% * 285 1.45 1.00
<br />EKG-147 240 :i:10% :i: 5% * 285 1.25 0.90
<br />EKG-148 Mercury Vapor 277 :i:10% :i: 5% * 285 1,08 0,80
<br />EKG-149 480 :i:10% :i: 5% * 285 0,62 0.50
<br />EKG-155 120 :i: 10% :i: 5% * 205 1.80 1,70
<br />EKG-156 175 Watt 208 :i: 10% :i: 5% * 205 1.00 0,98
<br />EKG-157 Mercury Vapor 240 :i:10% :i: 5% * 205 0,90 0.80
<br />EKG-158 277 :i:10% :i: 5% * 205 0.75 0,74
<br />EKG-159 480 :i:10% :i: 5% * 205 0.45 0.44
<br />Catalog number includes complete fixture as BALLAST lEGEND * Constant Wattage Autotransformer
<br /> . Core and Coil Voltage Stabilized
<br />described in specifications, page 4, including . Core and Coil lag
<br />arm and mounting hardware (less lamp). . Reactor
<br /> OPTIONS:
<br />STANDARDS: Cat No, description
<br />STANDARD LIGHT DISTRIBUTION TYPE II Fixture will be supplied with a reflector for ANSI type II, cut-off
<br />is ANSI type III, cut-off distribution, Refer to photometries on pages 12-26 for details,
<br /> MB.E "Medium Bronze" baked enamel, colored to match medium
<br />STANDARD FINISH is semi-gloss "black" bronze anodize as close as possible,
<br />baked enamel applied over a clear anodized MB-A "Medium Bronze" anodize
<br />base (fixture and arm) DB.A "Dark Bronze" anodize
<br /> BL-A "Black" anodize
<br /> A-15 120 volt photo cell All PHOTO CEllS ARE OPTIONAL.
<br /> A-16 208 volt photo cell Supplied pre-wired in fixture head
<br /> A-17 240 volt photo cell
<br /> A-18 277 volt photo cell (one per fixture) with sensor on top
<br /> A-19 480 volt photo cell s;de of fixture housing,
<br />ORDERING EXAMPLE:
<br /> ~~ q;- q;- .f ~
<br /> ~ ~,J (j
<br /> .0S .J ~ ~
<br /> ~~ (J'~ ~ ~
<br /> .'S~ ~~ ~~ (j tt' ~O)
<br /> ~(J ,~~ .p~
<br /> if-.!!:!f/i ~
<br /> ;,f-.!!:! Q-.!!:! ~O) ,~t'
<br /> ~b ~b ~b "'~ ,$ f/iCi)
<br /> ~,~ ~,~q, ~.!>.q, q,f/i '" "'Q
<br /> ~~ ~ q,'" ...... ~ Cf& t~
<br /> ~tJ' ~?S itJ'
<br /> ,~ ,~ ,~ Q~ Q~o
<br />
<br />)
<br />
<br />
<br />
<br />2B/EKG-100 {TYPE II} MB-A/ A-15/PTRSA-30B/MB-A
<br />
<br />see page 10 for wall mounts
<br />
<br />Kim Lighting, Ine, 5
<br />
|